tonyny Posted July 20, 2007 Report Share Posted July 20, 2007 Hi all, The dealer cut a new key for me today (driver 2) and also gave me a new fob/remote since the previous owner never turned in an extra set of keys. The problem I'm having is when ever I exit the car the seat settings etc go BACK to the driver 1 position, which is my wife's. Is this normal? Nothing like being crunched up to the steering wheel everytime I exit. Thanks for any info Also I have some black spots on the white roof that won't come off no matter what I try. Any tips appreciated "Capital punishment means never having to say, "You again"? Link to comment Share on other sites More sharing options...
thu Posted July 21, 2007 Report Share Posted July 21, 2007 You posted this same question in the other forum. I've duplicated my response, below: It looks like the exit position for your "Driver 2" needs to be programmed. Refer to your owners manual. It contains detailed information on how to do this. It's simple. Go and grab your owners manual and read it. 2003 Seville STS 43k miles with the Bose Sound, Navigation System, HID Headlamps, and MagneRide 1993 DeVille. Looks great inside and out! 298k miles! Link to comment Share on other sites More sharing options...
Bruce Nunnally Posted July 21, 2007 Report Share Posted July 21, 2007 I think you can set the exit position for each driver. Here is the info from the manual, this from the 02 page 2-100: https://www.mygmlink.com/pdf/go2content/man...2002seville.pdf Auto Exit Seat (If Equipped) This feature will move the driver’s seat to the previously programmed exit position when the ignition is turned off and the driver’s door is opened. Programmable Modes Mode 1: ON Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory. To determine the mode to which the vehicle is programmed or to program the vehicle to a different mode, do the following: 1. Enter FEATURE PROGRAMMING following the instructions listed previously. 2. Press the down arrow on the INFO button until AUTO EXIT SEAT appears on the DIC display. 3. To turn on the feature, press the ON/OFF button until ON appears on the DIC display. To turn it off, press the ON/OFF button until OFF appears on the display. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. Auto Exit Steering Wheel (If Equipped) This feature will move the column to the driver’s previously programmed exit position when the ignition is turned off and the driver’s door is opened. Programmable Modes Mode 1: ON Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 1. The mode to which the vehicle was programmed may have been changed since it left the factory. To determine the mode to which the vehicle is programmed or to program the vehicle to a different mode, do the following: 1. Enter FEATURE PROGRAMMING following the instructions listed previously. 2. Press the down arrow on the INFO button until AUTO EXIT STRG WHEEL appears on the DIC display. 3. To turn on the feature, press the ON/OFF button until ON appears on the DIC display. To turn it off, press the ON/OFF button until OFF appears on the display. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. Vehicle Programming and Personalization Features Your vehicle is equipped with personalization that allows you to program certain features to a preferred setting for up to two people. The number of programmable features varies depending upon which model of the vehicle is purchased. On all vehicles, features such as climate control settings, radio preset settings, exterior lighting at unlock, remote lock and unlock confirmation, and automatic door locks have already been programmed for your convenience. Some vehicles are equipped with additional features that can be programmed including the seat position, steering column position (if equipped) and outside mirror position. The navigation screen preferences (if equipped) will remain at the last set position. If your vehicle is equipped with the ability to program additional personalization features, the driver’s preferences are recalled by pressing the unlock button on the remote keyless entry transmitter or by pressing the appropriate memory button, 1 or 2, located on the driver’s door. Certain features can be programmed not to recall until the key is placed in the ignition. To change feature preferences you must use one of the following procedures. Entering Feature Programming To enter the feature programming mode, do the following: 1. Turn the ignition to ON, making sure the vehicle is in PARK (P). 2. If your vehicle has memory settings, press the appropriate memory button, 1 or 2, located on the driver’s door panel. The DIC display will show either 1 or 2 depending on which button was selected. 3. Press the INFO button until FEATURE PROGRAMMING appears on the DIC display. 4. Press the ON/OFF button to enter FEATURE PROGRAMMING. Bruce 2023 Cadillac CT4-V Blackwing Follow me on: Twitter Instagram Youtube Link to comment Share on other sites More sharing options...
tonyny Posted July 21, 2007 Author Report Share Posted July 21, 2007 You posted this same question in the other forum. I've duplicated my response, below: The more the merrier right? It looks like the exit position for your "Driver 2" needs to be programmed. Refer to your owners manual. It contains detailed information on how to do this. It's simple. Go and grab your owners manual and read it. Its NOT the exit program as I have that OFF on BOTH settings. The problem is the settings reverting back to Driver 1 when I remove the Driver *2* key from the ignition. here's my latest findings as I tried it once again: When I use the driver 1 key all works as its supposed to. Everything STAYS on driver 1 and nothing moves when I exit the car. When using the driver 2 fob to unlock the car the seats move to my position BUT when I put the key in and start the car the seat move to the driver 1 position! I have auto exit OFF on both settings so its not that. I also noticed that when I start the car with the driver 2 key the display first shows driver 2 than displays driver 1 right after along with playing my wife's radio station. And when I exit the car everything goes back to the driver 1 setting. Guess I need to go back to the dealer grrrrrrrrr "Capital punishment means never having to say, "You again"? Link to comment Share on other sites More sharing options...
thu Posted July 21, 2007 Report Share Posted July 21, 2007 You need to bring the car into the dealer. They'll use the tech2 tool to program the car to recognize the new key so that it acts as the "Driver 2" key. Right now, it doesn' t know what the heck key it is and so it acts as if it's the "Driver 1" key. 2003 Seville STS 43k miles with the Bose Sound, Navigation System, HID Headlamps, and MagneRide 1993 DeVille. Looks great inside and out! 298k miles! Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.