mrmilt Posted July 17, 2005 Report Share Posted July 17, 2005 Can any one tell me what the pcm 0741 codes is? My service engine light came on and I checked my codes and this is the one that showed up. The car is running fine but not sure if i have a problem. Thanks. Link to comment Share on other sites More sharing options...
bigjayzway Posted July 17, 2005 Report Share Posted July 17, 2005 P0471 - Exhaust Pressure Sensor Range/Performance I take it you have an obII system, as I do not see what year your car is? Big Jay Life is too short to grow up! Link to comment Share on other sites More sharing options...
Logan Posted July 17, 2005 Report Share Posted July 17, 2005 I took this from the 1999 year info....I dont know exactly what year you have, so some info may not be correct.... DTC P0741 TCC System Stuck Off Circuit Description The PCM controls the torque converter clutch (TCC) solenoid valve pulse width modulation (PWM). The solenoid controls the hydraulic fluid for TCC apply and release. When the TCC is applied, the engine is coupled directly to the transmission through the TCC. The TCC slip speed should be near 0. If the PCM detects high torque converter slip when the TCC is commanded ON, then DTC P0741 sets. DTC P0741 is a Type B DTC. Conditions for Running the DTC No MAF DTCs P0101, P0102, or P0103. No TP DTCs P0121, P0122, or P0123. No VSS DTCs P0502, or P0503. No A/T ISS DTCs P0716, or P0717. No TCC Stuck ON DTC P0742. No TFP manual valve position switch DTC P1810. No TCC PWM solenoid valve DTC P1860. The engine run time is greater than 5 seconds. The engine is not in fuel cut off. The TFP manual valve position switch indicates D4. The transmission gear ratio indicates 2nd, 3rd, or 4th gear. The transmission fluid temperature is -18-130°C (0-266°F). The throttle angle is greater than 8 degrees. Delivered torque is between 43-202 N·m (32-150 lb ft). The TCC solenoid valve is commanded ON at maximum duty cycle. Conditions for Setting the DTC TCC slip speed exceeds its limit for a given torque for 5 seconds. Torque (lb ft) Slip Speed Limit (RPM) 32 72 64 88 96 200 128 248 160 256 Action Taken When the DTC Sets The PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met. SERVICE ENGINE SOON, SERVICE TRANSMISSION displays on the driver information center (DIC). The PCM inhibits TCC engagement. The PCM inhibits 4th gear if the transmission is in hot mode. The PCM stores DTC P0741 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met. Conditions for Clearing the MIL/DTC The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes. A scan tool clears the DTC from PCM history. The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring. The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down the PCM. Diagnostic Aids Inspect the transmission fluid level. The transmission may be in hot mode. Inspect the transmission fluid lines to the radiator. The lines may be pinched, plugged or twisted. Test Description The numbers below refer to the step numbers on the diagnostic table. This step inspects the transmission fluid to ensure that it is at the proper level. This step verifies that the TCC engages when commanded ON by the scan tool. Logan Diagnostic LLC www.airbagcrash.com www.logandieselusa.com www.ledfix.com www.ledfix.com/yukontaillightrepair.html www.ledfix.com/ledreplacements.html www.ledfix.com/j42385toolrental.html Link to comment Share on other sites More sharing options...
bigjayzway Posted July 18, 2005 Report Share Posted July 18, 2005 P0471 OOPS 0741 My bad so sorry..Yeah do what Logan says! Big Jay Life is too short to grow up! Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.